Results 1 to 11 of 11

Thread: DOS with Dual reservoir issue seeing fluid levels.

  1. #1
    Regular Vistor cobraz's Avatar
    Join Date
    Jun 2013
    Location
    Atkinson NH
    Posts
    16

    DOS with Dual reservoir issue seeing fluid levels.

    I setup my DOS with Dual reservoir .. and it works fine.
    I have the graph of dosing...
    But, my level's graph does not show up ?

    How can I get that to show in Fusion ?
    Cable is attached.
    Attached Images Attached Images

  2. #2
    Frequent Visitor
    Join Date
    May 2016
    Location
    Lansdale, PA
    Posts
    589
    I assume you checked the unused tiles. Do you see the switches for the reservoirs? What do you mean by it works fine?

    My DOS did not recognize the switches or have the level tiles until I upgraded the firmware on the DOS, not the Apex box but the DOS box. Check configruation->module setup in the classic dashboard and on the bottom is list of your modules and the SW rev should be OK.

  3. #3
    Regular Vistor cobraz's Avatar
    Join Date
    Jun 2013
    Location
    Atkinson NH
    Posts
    16
    How did you update the firmware on the DOS - I cant find that anywhere on the site.

  4. #4
    Master Control Freak RussM's Avatar
    Join Date
    Dec 2012
    Location
    California - US Pacific
    Posts
    22,463
    Quote Originally Posted by cobraz View Post
    How did you update the firmware on the DOS - I cant find that anywhere on the site.
    Use the classic dashboard. Go to the Configuration -> Module Setup page. Look at the table at the bottom. If any module shows OLD in the Sw column, update it by using the upper part of the page. Watch for the update status to be shown in the middle of the page.
    Please do not send me PMs with technical questions or requesting assistance - use the forums for Apex help. PM me ONLY if the matter is of a private or personal nature. Thanks.

  5. #5
    New User
    Join Date
    Aug 2016
    Location
    atlanta, ga
    Posts
    2
    how do you update firmware for dos in fusion

  6. #6
    Master Control Freak RussM's Avatar
    Join Date
    Dec 2012
    Location
    California - US Pacific
    Posts
    22,463

    DOS with Dual reservoir issue seeing fluid levels.

    Quote Originally Posted by jjwash View Post
    how do you update firmware for dos in fusion
    Module update using Fusion is not available for Apex Classic models, but it is for the Apex 2016 model. Your profile here says you have a new one, so you can do it. Click the Expand button (3 gears) then click the Modules button. Select the DOS from the list. In the Action field, choose Update Firmware. Click the Send button to make it happen.
    Please do not send me PMs with technical questions or requesting assistance - use the forums for Apex help. PM me ONLY if the matter is of a private or personal nature. Thanks.

  7. #7
    New User
    Join Date
    Aug 2016
    Location
    atlanta, ga
    Posts
    2

    DOS with Dual reservoir issue seeing fluid levels.

    Quote Originally Posted by RussM View Post
    Module update using Fusion is not available for Apex Classic models, but it is for the Apex 2016 model. Your profile here says you have a new one, so you can do it. Click the Expand button (3 gears) then click the Modules button. Select the DOS from the list. In the Action field, choose Update Firmware. Click the Send button to make it happen.
    That worked thanks

  8. #8
    New User
    Join Date
    Sep 2016
    Location
    Vancouver, Canada
    Posts
    1
    Hi...i am a new here. I want to know if you see the switches for the reservoirs? What do you mean by it works fine? In my case DOS did not recognize the switches or have the level tiles until I upgraded the firmware on the DOS, not the Apex box but the DOS box. Check configruation->module setup in the classic dashboard and on the bottom is list of your modules and the SW rev should be fine.

  9. #9
    New User
    Join Date
    May 2015
    Location
    US, Pacific
    Posts
    2
    Ok i have done everything stated here to get the DŌS DUAL RESERVOIRto show up on the dash board. When i first installed it everything worked fine then today it was gone from the dashboard!

  10. #10
    New User
    Join Date
    Feb 2015
    Location
    Buffalo NY
    Posts
    1
    I'M having same problem,installed it six Months ago everything on screen and working fine but two day ago, DŌS DUAL RESERVOIR disappeared from my screen

  11. #11
    New User
    Join Date
    Aug 2016
    Location
    Hawaii
    Posts
    4
    Did this issue get resolved? I am having the same issue after updating the Apex firmware. Thanks.

Similar Threads

  1. Dual heater program issue
    By Flagg37 in forum Apex Programming for Heaters and Chillers
    Replies: 23
    Last Post: 10-13-2017, 19:09
  2. DDR not measuring fluid levels?
    By jam583 in forum DŌS & DDR – Dosing and Fluid Metering System
    Replies: 3
    Last Post: 12-28-2015, 12:47
  3. DDR - DOS Dual Reservoir shipping to dealers this week
    By Terence in forum News and Announcements
    Replies: 22
    Last Post: 09-30-2015, 21:16
  4. Help! Ato reservoir dual switch programming
    By Coolbreezecs in forum Apex Programming for Dosing, ATO, and AWC
    Replies: 14
    Last Post: 05-03-2015, 08:21
  5. Dual Dos Reservoir?
    By puggleman in forum DŌS & DDR – Dosing and Fluid Metering System
    Replies: 29
    Last Post: 04-08-2015, 13:05

Bookmarks

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •