Results 1 to 6 of 6

Thread: Waveline Cable Pinout for VS1/2

  1. #1
    Frequent Visitor Reeffish's Avatar
    Join Date
    Nov 2016
    Location
    US, Central
    Posts
    89

    Waveline Cable Pinout for VS1/2

    Can someone give me the easy to understand version of where the Ethernet wires go on the controller end of the cat5 cable?

    I want to control 2 Waveline pumps with a single VS Port. I'm using T568-B pinout on the Apex side.

    Which wires go into which RJ45 plug for which pump?

    Thanks


    Sent from my iPhone using Tapatalk

  2. #2
    Frequent Visitor
    Join Date
    May 2017
    Location
    Lynn, MA
    Posts
    112
    THis I found on the Forum when I was looking for the same info


    Sent from my iPad using Tapatalk Pro

  3. #3
    Frequent Visitor Reeffish's Avatar
    Join Date
    Nov 2016
    Location
    US, Central
    Posts
    89
    Thanks...
    Ok, that's one, what about the second pump


    Sent from my iPhone using Tapatalk

  4. #4
    Frequent Visitor
    Join Date
    May 2017
    Location
    Lynn, MA
    Posts
    112
    I think 5 & 6 was the other 0-10V signal. This is the link to the forum about this.
    https://forum.neptunesystems.com/sho...-working/page2



    Sent from my iPad using Tapatalk Pro

  5. #5
    Frequent Visitor Reeffish's Avatar
    Join Date
    Nov 2016
    Location
    US, Central
    Posts
    89

    Waveline Cable Pinout for VS1/2

    Ok, don't know what some of these jokers have been smoking....but here's what worked for me:

    1. Make one end of the ethernet cable to T568-B specs.

    On the other end:

    1. For VSP1 pin positions 5 & 6 with blu /whi (5) grn (6) [5 is + voltage and 6 is ground]

    2. For VSP2 pin potions 5 & 6 with org/whi (5) & org (6). [5 is + voltage and 6 is ground].

    As always check with voltage meter with VSP sliders to ON position for around 10 vdc, prior to crimping.


    Sent from my iPhone using Tapatalk

  6. #6
    Frequent Visitor Reeffish's Avatar
    Join Date
    Nov 2016
    Location
    US, Central
    Posts
    89
    I should also note that I have the Apex 2016


    Sent from my iPhone using Tapatalk

Similar Threads

  1. 1Link Pinout
    By bzofiq in forum DIY
    Replies: 4
    Last Post: 01-30-2019, 13:20
  2. Question: FMM 3.5mm jack pinout
    By Dan_B in forum Fluid Monitoring Module (FMM), FMK, ATK, LDK, and FMM Accessories
    Replies: 1
    Last Post: 01-19-2019, 22:49
  3. Question: Anyone have the RJ11 pinout documentation for the temp probe?
    By J3FF in forum Apex Classic/Apex Lite/Apex Jr
    Replies: 0
    Last Post: 02-28-2018, 15:48
  4. pinout of mini din connector
    By jonnyk in forum AquaBus Modules, Probes, and Breakout Boxes
    Replies: 2
    Last Post: 12-04-2017, 16:54
  5. Question on Kessil pinout
    By shoggoth43 in forum DIY
    Replies: 2
    Last Post: 04-08-2016, 08:49

Bookmarks

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •