Results 1 to 8 of 8

Thread: Tunze

  1. #1
    New User
    Join Date
    Sep 2017
    Location
    pacific
    Posts
    4

    Tunze

    I have 4 tunze 6105s connected to my apex and I cant figure out how to get them to oscillate to create a wave. Any help would be appreciated. I have them connected thru the VS1 and VS2 ports but when I plug them in they all come on even though the apev vs is off.

  2. #2
    New User
    Join Date
    Sep 2017
    Location
    pacific
    Posts
    4
    anyone?

  3. #3
    Frequent Visitor
    Join Date
    May 2014
    Location
    Portugal
    Posts
    389
    Use profiles ...

    in tunze outlet

    Set PF1


    PF1 profile
    Initial off time (Seconds)On time (Seconds)Off time (Seconds)Minimum intensityMaximum intensity

  4. #4
    New User
    Join Date
    Sep 2017
    Location
    pacific
    Posts
    4

    Tunze

    Quote Originally Posted by Rui Manuel Gaspar View Post
    Use profiles ...

    in tunze outlet

    Set PF1


    PF1 profile
    Initial off time (Seconds)On time (Seconds)Off time (Seconds)Minimum intensityMaximum intensity
    Its all so confusing for me. I cant believe they made it this complicated. I had an Aqua Controller before this and it was much easier to set up.
    I called the support line and they told me to go to the forum and read what everyone else is doing. Although it has been somewhat helpful Im completely baffled. Now Im trying to program my kalk stirrer to come on for 1 min every hour and again Im stuck. any help would be appreciated.

    - - - Updated - - -

    Quote Originally Posted by Rui Manuel Gaspar View Post
    Use profiles ...

    in tunze outlet

    Set PF1


    PF1 profile
    Initial off time (Seconds)On time (Seconds)Off time (Seconds)Minimum intensityMaximum intensity
    Its all so confusing for me. I cant believe they made it this complicated. I had an Aqua Controller before this and it was much easier to set up.
    I called the support line and they told me to go to the forum and read what everyone else is doing. Although it has been somewhat helpful Im completely baffled. Now Im trying to program my kalk stirrer to come on for 1 min every hour and again Im stuck. any help would be appreciated.

  5. #5
    New User
    Join Date
    Sep 2017
    Location
    pacific
    Posts
    4
    What do you think? The following is what I came up with based on the what Ive been reading.

    power heads 2 and 4
    Set PF1
    set off time 0060
    set on time 0060
    set off time 0000
    set PF1 minimum intensity 35%
    set PF1 maximum intensity 100%

    Power head 1 and 3
    Set PF1
    set off time 0000
    set on time 0060
    set off time 0060
    set PF1 minimum intensity 35%
    set PF1 maximum intensity 100%

  6. #6
    Frequent Visitor
    Join Date
    May 2014
    Location
    Portugal
    Posts
    389
    Hummm something is not right

    ok. go to VarSpd ports 1,2,3 and 4 and write:
    Fallback OFF
    Set <profile_name> (you can use 4 diferent profiles or use 2 and attach it to what ever VarSpd port you want).

    I am assuming you are using 4x Tunze according to your description.

    Then setup your profiles like Tunze1, Tunze2, Tunze3 and Tunze4. Don't forget to look at the "divide by 10" as by your parameters you will have 60s at 35% and then 60s at 100%
    Also look at the synchronise feature as you might want to sync/anti-sync VarSpd 1 and 2 ... and VarSpd 3 and 4

    For the Kalk Stirrer ... Use OSC command in the outlet that controls the Kalk motor

    OSC 000:00/000:01/059:59 Then ON

    Hope this helps!

  7. #7
    Master Control Freak RussM's Avatar
    Join Date
    Dec 2012
    Location
    California - US Pacific
    Posts
    22,463
    The OSC statement for the kalk stirrer should be:

    OSC 000:00/001:00/0059:00 Then ON

    The one given earlier only would only turn the outlet on for 1 second
    Please do not send me PMs with technical questions or requesting assistance - use the forums for Apex help. PM me ONLY if the matter is of a private or personal nature. Thanks.

  8. #8
    Frequent Visitor
    Join Date
    May 2014
    Location
    Portugal
    Posts
    389
    Thanks for the correction Russ ... typing to fast out of my head instead of reading the manual!

Similar Threads

  1. Help! Tunze
    By Rally on in forum Apex Programming for Vortech, Tunze, & Other Controllable Pumps
    Replies: 5
    Last Post: 03-05-2020, 05:49
  2. (4) Tunze 6105-Tunze Y Adapter to one VDM port
    By m3lacoste in forum Apex Programming for Vortech, Tunze, & Other Controllable Pumps
    Replies: 1
    Last Post: 01-30-2017, 15:51
  3. Question: Tunze Osomolator/Tunze Pumps
    By krzyphsygy in forum Pre-Sales Questions
    Replies: 1
    Last Post: 06-09-2014, 11:21
  4. Help! moving 4 tunze 6055's from tunze contol to apex
    By Lucifa in forum Apex Programming for Vortech, Tunze, & Other Controllable Pumps
    Replies: 3
    Last Post: 03-12-2014, 17:21
  5. Question: Does the Tunze VDM module support Tunze Lights?
    By ggoosen in forum Pre-Sales Questions
    Replies: 5
    Last Post: 01-26-2014, 16:03

Bookmarks

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •