Results 1 to 7 of 7

Thread: WAV newbie questions

  1. #1
    New User
    Join Date
    Dec 2016
    Location
    Gainesville, FL
    Posts
    7

    WAV newbie questions

    I connected pair of WAVs yesterday and have tried to find answers to these questions everywhere but cannot.

    First, what is the "OK, 100%" mean. I adjusted the percentages in the points of the program to not go above 50%. I'm puzzled as to why it says 100%.
    Screen Shot 2018-02-20 at 4.12.14 PM.png
    And secondly, what does this slide bar do? I've read the WAV manual, but the screenshots are for Apex Classic not fusion.
    Screen Shot 2018-02-20 at 4.15.34 PM.png

    Thank you!!

  2. #2
    Frequent Contributor zombie's Avatar
    Join Date
    Dec 2013
    Location
    Denver, CO
    Posts
    13,176
    Not sure why it's showing 100%, you remembered to send the update to the apex right?

    The sliders change the timing of the pulse. Further to the right makes the timing of the pulse longer.

    You might be an engineer if...You have no life and can prove it mathematically.

  3. #3
    New User
    Join Date
    Dec 2016
    Location
    Gainesville, FL
    Posts
    7
    Thank you! Yes, I saved the settings. I even deleted the pre-programmed scheme I initially downloaded and made my own. My corals and fish are hanging on for dear life each time I try again and turn the WAVs back on. I put some smaller powerheads in temporarily until I can get this pair of WAVs figured out. Regardless of the scheme, they are both running at 100% all the time.

  4. #4
    Frequent Contributor zombie's Avatar
    Join Date
    Dec 2013
    Location
    Denver, CO
    Posts
    13,176
    Click the gear and go to the advanced tab. If it isn't empty, post the code you see here.

    You might be an engineer if...You have no life and can prove it mathematically.

  5. #5
    New User
    Join Date
    Dec 2016
    Location
    Gainesville, FL
    Posts
    7
    This is it and it's just what I put in to test them before I start playing with more advanced programming.
    Fallback OFFSet ON
    If FeedA 000 Then OFF

  6. #6
    Frequent Contributor zombie's Avatar
    Join Date
    Dec 2013
    Location
    Denver, CO
    Posts
    13,176
    That is exactly why it's always at 100%. Delete the set ON in there as the advanced tab overrides anything in the wizard when true (you can keep the feed and fallback statements if you want).

    You might be an engineer if...You have no life and can prove it mathematically.

  7. #7
    New User
    Join Date
    Dec 2016
    Location
    Gainesville, FL
    Posts
    7
    Ah ok. Thanks so much!!! I figured ON just meant ON not 100% on. haha I'm glad you're smart ;-)

Similar Threads

  1. alarm messages- newbie questions
    By yraveh in forum APEX Fusion
    Replies: 0
    Last Post: 12-09-2019, 08:24
  2. Wav questions
    By shoggoth43 in forum Pre-Sales Questions
    Replies: 2
    Last Post: 04-12-2016, 10:28
  3. Newbie Wav program question
    By 3daughters in forum Apex Programming for Vortech, Tunze, & Other Controllable Pumps
    Replies: 0
    Last Post: 12-22-2015, 11:57
  4. Questions from newbie doing first firmware update!!
    By Glreynolds in forum Updating Apex Classic Firmware & Web Pages
    Replies: 7
    Last Post: 01-05-2015, 07:07
  5. Newbie/ LSM module questions
    By Firemountain in forum Pre-Sales Questions
    Replies: 2
    Last Post: 07-15-2014, 04:04

Bookmarks

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •