Results 1 to 4 of 4

Thread: Atk, ldk

  1. #1
    Regular Vistor
    Join Date
    Dec 2017
    Location
    US Miami
    Posts
    45

    Atk, ldk

    My ATK is not going ON to be refilling the sump where my sensors are located. They are being there for a year until I recently added a new Eba832 and I hook it up to this devise since this pass Saturday I being bombarded with alert emails that Thank God cause the return was almost empty this is how is programmed

    Fallback OFF
    Set ON
    If ATKLOW (ATK low optic sensor) open then off
    if ATKHIG ( ATK high optics sensor) CLOSED THEN OFF
    DEFER OO5:OO THEN OFF
    MIN TIME 050:00 THEN OFF
    DEFER 000:30 THEN ON
    DEFER 000:10 THEN OFF

    my LDK is also not working I connected as per the instructions on the Get Started but I put s
    little of water and nothing happens and I constantly opening and closing and sending me notification

    the Alert configuration is as this
    Set OFF
    if error ATK_2_8 then ON
    IF ATKLOW CLOSED THEN ON
    IF FLOOR (wet sensor) CLOSED THEN ON
    IF SUMP (sensor inside the cabinet next to sump)CLOSED THEN ON
    IF SUMP CLOSED THEN ON
    Please, Please, Please
    i need help and before all my questions have been answer here.
    thank You 🤯

  2. #2
    Frequent Contributor zombie's Avatar
    Join Date
    Dec 2013
    Location
    Denver, CO
    Posts
    13,176
    Check your logs to make sure it's really not filling. The min time statement that forces it to wait for 50 minutes between fills can sometimes give the impression it's not filling when it really is.

    Verify that the pump turns on when set to manual ON.

    Verify that the sensors are showing the correct state.

    Make sure all items connected to the FMM are set to optical or leak not auto-detect.

    Update the module firmware of the FMM.


    You might be an engineer if...You have no life and can prove it mathematically.

  3. #3
    Master Control Freak RussM's Avatar
    Join Date
    Dec 2012
    Location
    California - US Pacific
    Posts
    22,466
    Your programming for the ATK is wrong:

    Fallback OFF
    Set ON // should be: Set OFF
    If ATKLOW (ATK low optic sensor) open then off // Should be: If ATKLOW OPEN then ON
    if ATKHIG ( ATK high optics sensor) CLOSED THEN OFF
    DEFER OO5:OO THEN OFF // Delete this; you can only have one Defer ##:## Then OFF statement.
    MIN TIME 050:00 THEN OFF
    DEFER 000:30 THEN ON
    DEFER 000:10 THEN OFF

    Also, please do not just type in your programming; there are obvious typing errors here. - ALWAYS copy and paste your programming into forum posts so we see exactly what the Apex has.
    Please do not send me PMs with technical questions or requesting assistance - use the forums for Apex help. PM me ONLY if the matter is of a private or personal nature. Thanks.

  4. #4
    Regular Vistor
    Join Date
    Dec 2017
    Location
    US Miami
    Posts
    45
    i also have a leak detector and sensor 1 & 2 are set to water on floor, but constantly sensor one is opening and close, is this normal?
    what was inside the parenthesis was to show you in the forum what it means, i wish i know how to copy and paste here in the forum.
    Fallback OFF
    Set OFF
    If ATKLOW OPEN Then ON
    If ATKHIG CLOSED Then OFF
    Min Time 050:00 Then OFF
    Defer 000:30 Then ON
    Defer 000:10 Then OFF
    i think i just learned how to copy , check this Todd,


    this is my configuration on the 24 v aquabus, is this correct?
    ThFallback OFF
    Set OFF
    If ATKHIG OPEN Then ON
    If ATKLOW CLOSED Then OFF
    If ATKHIG CLOSED Then OFF
    If ATKSUM OPEN Then OFF
    When On > 005:00 Theen OFF
    n OFF
    Defer 000:10 Then ON
    Defer 000:04 Then OFF
    Min Time 060:00

    this programing should be like the one on top
    if I press on it will refill but is not doing it I AUTO
    Last edited by CUBAN REEFER; 03-06-2018 at 06:48. Reason: am learning how to program

Similar Threads

  1. LDK Configuration
    By DaveKGold in forum Fluid Monitoring Module (FMM), FMK, ATK, LDK, and FMM Accessories
    Replies: 3
    Last Post: 10-01-2019, 22:06
  2. Question: LDK
    By shellsea in forum Misc Apex Usage & Programming
    Replies: 5
    Last Post: 03-02-2019, 08:01
  3. Review My Program Skimmer with LDK
    By Navymedic in forum Misc Apex Usage & Programming
    Replies: 1
    Last Post: 01-25-2019, 19:48
  4. LDK outside of US?
    By Clownfishy in forum Fluid Monitoring Module (FMM), FMK, ATK, LDK, and FMM Accessories
    Replies: 1
    Last Post: 04-21-2018, 06:55
  5. Review My Program LDK
    By CUBAN REEFER in forum Fluid Monitoring Module (FMM), FMK, ATK, LDK, and FMM Accessories
    Replies: 8
    Last Post: 03-05-2018, 19:59

Bookmarks

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •