Results 1 to 3 of 3

Thread: Vortech MP10 Help

  1. #1
    New User
    Join Date
    Mar 2018
    Location
    Lafayette, IN
    Posts
    2

    Vortech MP10 Help

    Hello, I've just recently begun entertaining the idea of implementing micro bubble scrubbing into my bio cube. I'm trying to set up a profile for my MP10 to where when Outlet "AirPump" is ON, then the MP10 will go into Long Pulse mode at 100% for 5 minutes, and then off for 30 seconds. Problem is, I can't figure out the code for it! I currently have this programmed:

    Fallback ON
    tdata 00:00:00,0,0,40,0,0,0,0,0,0,0,0,0,0
    tdata 06:00:00,0,0,90,1,0,0,0,0,0,0,0,0,0
    tdata 09:00:00,0,0,80,2,0,0,0,0,0,0,0,0,0
    tdata 10:00:00,0,0,60,0,0,0,0,0,0,0,0,0,0
    tdata 12:00:00,0,0,75,7,0,0,0,0,0,0,0,0,0
    tdata 14:00:00,0,0,60,0,0,0,0,0,0,0,0,0,0
    tdata 16:00:00,0,0,100,3,226,4,0,0,0,0,0,0,0
    tdata 17:00:00,0,0,95,1,0,0,0,0,0,0,0,0,0
    tdata 20:00:00,0,0,80,2,0,0,0,0,0,0,0,0,0
    tdata 21:00:00,0,0,60,0,0,0,0,0,0,0,0,0,0
    tdata 22:00:00,0,0,40,0,0,0,0,0,0,0,0,0,0
    If Output AirPump = ON Then 100
    If FeedA 000 Then OFF
    If FeedD 000 Then 0

    You'll notice that it says "If Output AirPump = ON Then 100.....problem is when I turn on the airpump outlet, the mp10 only runs at "Constant 50%". Can anyone help?

  2. #2
    Frequent Contributor zombie's Avatar
    Join Date
    Dec 2013
    Location
    Denver, CO
    Posts
    13,176
    Make a profile of type vortech with the parameters you want then in the air pump name call out that profiles name instead of 100.

    You might be an engineer if...You have no life and can prove it mathematically.

  3. #3
    New User
    Join Date
    Mar 2018
    Location
    Lafayette, IN
    Posts
    2
    Being new to the Apex, it took me a while to figure out how to make a profile, but with a little googling, and youtubing I was able to get it in there. I wasn't able to do the On/OFF/On pulse like I wanted because the pump just wouldn't run at 100%. So I just set it at constant and 100 within the profile. Then in my code I put If Output AirPump = ON then Bubbles (which is what I named the profile). Thank you for your help!

Similar Threads

  1. Help! Vortech MP10 Pump Missing !?!
    By Mike's Reef in forum Apex Programming for Vortech, Tunze, & Other Controllable Pumps
    Replies: 0
    Last Post: 08-07-2019, 14:11
  2. Vortech MP10 not following program
    By Greego in forum Apex Programming for Vortech, Tunze, & Other Controllable Pumps
    Replies: 4
    Last Post: 12-13-2016, 19:22
  3. VorTech MP10
    By superdoc in forum Pre-Sales Questions
    Replies: 1
    Last Post: 05-17-2015, 10:44
  4. Help! No outlet created for Vortech MP10
    By stevematt21 in forum Apex Programming for Vortech, Tunze, & Other Controllable Pumps
    Replies: 11
    Last Post: 08-21-2014, 04:26
  5. Help! Vortech MP10 Error code...
    By DjWall*E in forum AquaBus Modules, Probes, and Breakout Boxes
    Replies: 1
    Last Post: 12-08-2013, 20:03

Bookmarks

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •