Results 1 to 6 of 6

Thread: WXM Not Responding to Fusion Changes. Stuck at 100%

  1. #1
    New User
    Join Date
    Jun 2018
    Location
    Fort Lauderdale Florida Eastern Time Zone
    Posts
    3

    WXM Not Responding to Fusion Changes. Stuck at 100%

    Hello Everyone,

    New to all of this. Set up my apex classic which was removed from a friends tank. I cleared the system of the old user and its working well on my tank. When setting up the system it went smooth.

    I am running into some WXM issues with my mp10's. first only one will connect which i think is a pump problem because the lights are all jacked up too.

    The one pump i can connect is having the issue. i have failed to find any answers on the forums. i can turn it on and off via fusion, but when i change the sliders up and down to configure the mp10 its stuck on constant 100%.

    I tried disconnecting the mp10's power and that didn't work. next i tried powering off the wxm. nope didn't work. Lastly i tried clearing and reconnecting the mp10 and that didn't work..

    I know you guys are the best around so what do you recommend???

    thanks
    kris
    Last edited by SaltFlyTyer; 06-26-2018 at 20:14. Reason: I can’t spell

  2. #2
    Frequent Contributor zombie's Avatar
    Join Date
    Dec 2013
    Location
    Denver, CO
    Posts
    13,176
    Make sure the firmware for the WXM is current in the classic dashboard and make sure the mp10s firmware is also current.

    Sent from my SM-G965U using Tapatalk

  3. #3
    New User
    Join Date
    Jun 2018
    Location
    Fort Lauderdale Florida Eastern Time Zone
    Posts
    3
    Thank you for the reply.

    I know how to check the wxm firmware and it is up to date advising (ok) on the classic dashboard.

    I’m gonna have to research how to check the mp10 firmware, and possibly update it.

  4. #4
    Frequent Visitor
    Join Date
    Mar 2015
    Location
    San Jose,CA
    Posts
    528
    Screen shots of your fusion dashboard showing the Vortech outlet and also of the configuration page.


    Sent from my iPhone using Tapatalk

  5. #5
    New User
    Join Date
    Jun 2018
    Location
    Fort Lauderdale Florida Eastern Time Zone
    Posts
    3
    Here are the screen shots. I had to disconnect the pump because it was getting hot on the dry side. Where is says “missing” now it said “cnst100%” when I was having the problems.
    64D9CF95-2EDB-4E09-AFB6-B1B6380F235C.jpg9EADE135-9EEF-41BB-82BF-6F7C5D5F5A25.jpg

  6. #6
    New User
    Join Date
    Dec 2018
    Location
    CALIFORNIA
    Posts
    5
    A member of the Neptune Facebook group fixed the issue for me. I had added a 'Set ON' command in the advanced configuration tab. I had added the command as part of a feeding routine.

    Deleting the 'Set ON' line solved the '100% continuous' problem and the votech started running the profile in fusion.

Similar Threads

  1. WXM Vortech Programming stuck?
    By etszoo in forum Apex Programming for Vortech, Tunze, & Other Controllable Pumps
    Replies: 4
    Last Post: 03-22-2017, 16:33
  2. Help! WXM/Radions and AFS on Aquabus Not Responding
    By dhaen in forum A2 Apex/ApexEL and A3 Apex Pro/Apex/Apex Jr
    Replies: 1
    Last Post: 03-17-2017, 21:50
  3. WXM Vortech Programming stuck?
    By etszoo in forum AquaBus Modules, Probes, and Breakout Boxes
    Replies: 0
    Last Post: 03-16-2017, 14:41
  4. can't get 100% in pulse mode with wxm controlling mp40wqd
    By rckrzy1 in forum Apex Programming for Vortech, Tunze, & Other Controllable Pumps
    Replies: 7
    Last Post: 06-20-2015, 14:06
  5. Help! WXM firmware update issue (stuck on 1.11)
    By kgk in forum Apex Classic/Apex Lite/Apex Jr
    Replies: 5
    Last Post: 12-08-2014, 01:11

Bookmarks

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •