Results 1 to 4 of 4

Thread: ATK Not Turning On

  1. #1
    Regular Vistor
    Join Date
    Nov 2015
    Location
    US, Central
    Posts
    35

    ATK Not Turning On

    I have been running this configuration for at least 6 months without issue. Over the last few days, I have noticed by ATK switch on the console turning itself OFF. It has done this in the past after the pump had run for more than 5 minutes so I switched it back on Auto.

    Today I did the same when I saw it OFF and went to check to make sure it was running. It wasn't. So I switched the Outlet to ON.. Nothing.

    Outlet says it is ON, PMUP isn't running. No clog, impeller looks fine. Only run in RODI water so no Kalk issues.

    Here is my program for reference: Note, I did switch it to 10 min max run time to validate it wasn't going over the 5 minutes before I realized it was not running at all.

    Fallback OFF
    Set OFF
    If Swx10_1 OPEN Then ON
    If Swx10_2 CLOSED Then OFF
    If Power Apex Off 005 Then OFF
    When On > 010:00 Then OFF
    Defer 000:15 Then ON
    Defer 000:15 Then OFF
    Min Time 060:00 Then OFF

    Next steps in troubleshooting?

  2. #2
    Regular Vistor
    Join Date
    Nov 2015
    Location
    US, Central
    Posts
    35
    ... how about making sure the power isn't plugged into an EB8 Outlet that has the power OFF

    At least it got me to upgrade my module firmware!!!

  3. #3
    Frequent Contributor zombie's Avatar
    Join Date
    Dec 2013
    Location
    Denver, CO
    Posts
    13,176
    Quote Originally Posted by jmheron View Post
    ... how about making sure the power isn't plugged into an EB8 Outlet that has the power OFF

    At least it got me to upgrade my module firmware!!!
    Funny. Number one rule of electrical troubleshooting...is it plugged in.

    Sent from my SM-G965U using Tapatalk

  4. #4
    Regular Vistor
    Join Date
    Nov 2015
    Location
    US, Central
    Posts
    35
    Haha, it was plugged in... but the outlet was OFF.... Darn it!

Similar Threads

  1. ATK not Turning ON
    By fishyfish22 in forum Fluid Monitoring Module (FMM), FMK, ATK, LDK, and FMM Accessories
    Replies: 2
    Last Post: 08-29-2020, 10:28
  2. Help! ATK not turning of during AWC cycle
    By 650 Bob in forum Apex Programming for Dosing, ATO, and AWC
    Replies: 2
    Last Post: 06-14-2020, 00:34
  3. ATK Turning off
    By fishynyc in forum Fluid Monitoring Module (FMM), FMK, ATK, LDK, and FMM Accessories
    Replies: 2
    Last Post: 07-31-2019, 14:12
  4. ATK turning on/off quickly
    By ltcolspit in forum Fluid Monitoring Module (FMM), FMK, ATK, LDK, and FMM Accessories
    Replies: 4
    Last Post: 03-29-2019, 13:16
  5. ATK turning from Auto to OFF
    By jester17 in forum Fluid Monitoring Module (FMM), FMK, ATK, LDK, and FMM Accessories
    Replies: 3
    Last Post: 09-01-2017, 14:28

Bookmarks

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •