Results 1 to 10 of 10

Thread: Cor Program doesn't save

  1. #1
    New User
    Join Date
    Jun 2018
    Location
    Grand Junction, CO
    Posts
    9

    Cor Program doesn't save

    I am trying to have my Cor start at 70% and ramp to 100% over 5 minutes. I made a ramp profile to do it, but when I try to add Set profile name in Cor advanced tab, it doesn't highlight the update button, and my program doesn't save. If I exit and come back in, the only code that it hangs on to is "If FeedA 000 Then OFF". It doesn't keep any changes that I make to that line either, unless I change something on the Basic tab at the same time. What am I doing wrong?

  2. #2
    Frequent Contributor zombie's Avatar
    Join Date
    Dec 2013
    Location
    Denver, CO
    Posts
    13,176
    Did you change profilename to what you named your profile?

    Sent from my SM-G965U using Tapatalk

  3. #3
    New User
    Join Date
    Jun 2018
    Location
    Grand Junction, CO
    Posts
    9
    Yes...It is: Cor_Start

  4. #4
    Frequent Contributor zombie's Avatar
    Join Date
    Dec 2013
    Location
    Denver, CO
    Posts
    13,176
    I think your problem is forgetting to press OK in the advanced tab before closing it to press update. Regardless for this type of program, the wizard is not the ideal location to do your programming. You are better off doing it in the advanced output configuration instead of the advanced tab of the wizard.

    Sent from my SM-G965U using Tapatalk

  5. #5
    New User
    Join Date
    Jun 2018
    Location
    Grand Junction, CO
    Posts
    9
    Nope...I'm definitely hitting OK, but the Update button never turns orange. I can change the program on other outputs, like my skimmer, and it works just fine. For some reason, it just seems to affect the Cor programming. I've also tried doing it through the output configuration, and that didn't work either, but honestly, I can't tell the difference between accessing the program screen from outputs and accessing it from settings on the Dashboard. Seems like they both take me to the same place.

  6. #6
    Frequent Contributor zombie's Avatar
    Join Date
    Dec 2013
    Location
    Denver, CO
    Posts
    13,176
    When I say output configuration, I'm referring to this, not how you get to the programming.

    Sent from my SM-G965U using Tapatalk

  7. #7
    New User
    Join Date
    Jun 2018
    Location
    Grand Junction, CO
    Posts
    9
    Oh...my bad...but that is where I'm going.

  8. #8
    New User
    Join Date
    Jun 2018
    Location
    Grand Junction, CO
    Posts
    9
    Here's a screen shot. Just added the first two lines, but update doesn't turn yellow, even after I hit ok.
    pic.jpg

  9. #9
    Frequent Contributor zombie's Avatar
    Join Date
    Dec 2013
    Location
    Denver, CO
    Posts
    13,176
    Dont do it there. That adds a whole bunch of unnecessary code. Click this to go to the correct configuration screen for this application.



    Sent from my SM-G965U using Tapatalk

  10. #10
    New User
    Join Date
    Jun 2018
    Location
    Grand Junction, CO
    Posts
    9
    OMG....That was EXACTLY the problem. THANK YOU so much from saving the wall that I was beating my head against.

Similar Threads

  1. Cor-20 Ramp On program help
    By isomorphic85 in forum COR-15 & COR-20 Pumps
    Replies: 29
    Last Post: 03-24-2022, 12:16
  2. Can Someone Explain Why This Light Program Doesn't Work?
    By raylinds in forum Apex Programming for Lighting
    Replies: 4
    Last Post: 11-11-2020, 08:53
  3. Question: Cor 15 Program question
    By bhbbhb in forum COR-15 & COR-20 Pumps
    Replies: 1
    Last Post: 05-26-2020, 14:57
  4. Cor 15 program
    By mengchhorn in forum COR-15 & COR-20 Pumps
    Replies: 10
    Last Post: 01-28-2020, 05:45
  5. Help! Unable to save advanced eb outlet program
    By zsteph in forum Apex Programming for Lighting
    Replies: 2
    Last Post: 01-28-2013, 19:20

Bookmarks

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •