Results 1 to 5 of 5

Thread: DOS dosing incorrect volumes (AWC setup)

  1. #1
    Regular Vistor
    Join Date
    Nov 2015
    Location
    US, Central
    Posts
    35

    DOS dosing incorrect volumes (AWC setup)

    I have read some details around there being a potential bug that engineering is working through where they are troubleshooting the graph not showing the correct amounts. Not sure if this is my issue, but if it is, please point me towards the details if you know where it is

    MY issue:

    I have two DOS units, one for dosing Calc and Alk (working perfectly) and another I just purchased for AWC. Set up through the calibration and set to dose 3785.4ml a day. The first head shows it hits that amount every day where the second head always shows 3756.3, always!

    Now I have a 250g system, so the ~29 ml a day isn't going to cause me much issue, but I'd like to have a perfectly working unit.

    I did install this without following the directions perfectly (HAHA) but I don't believe the fact that I swapped the in/out makes much of a difference since it is supposed to move the same volume for each head. Below is a snapshot of code and dashboard.

    DOS AWC 1.JPG

    DOS AWC 2.JPG



    Any help appreciated!

  2. #2
    Regular Vistor
    Join Date
    Nov 2015
    Location
    US, Central
    Posts
    35
    So I went through the dosing log and noticed that in the beginning doses going "OUT" (Head 1) were an ODD number and "IN" (Head 2) was an EVEN number.

    I went to the end to divide the totals by 2 and calculate the total added to determine if it was right and they were backwards... "OUT" was now EVEN and "IN" was now ODD.

    Turns out, I'm missing a dose on 10/10 at 15:26:34 -0500 for "IN".. Pic below

    Dose Missed Log.JPG

    And another missed dose for "IN" on 10/3.. pic below

    Dose Missed Log 2.JPG

    I also noticed a missed Calcium dose for my ALK/CAL which is more concerning for me.

  3. #3
    Regular Vistor
    Join Date
    Nov 2015
    Location
    US, Central
    Posts
    35
    Anyone?

    #Mods would it be possible to change the title to DOS - Missing Dose

  4. #4
    Regular Vistor
    Join Date
    Nov 2015
    Location
    US, Central
    Posts
    35
    Bump!

    Sent from my SAMSUNG-SM-G930A using Tapatalk

  5. #5
    Frequent Contributor zombie's Avatar
    Join Date
    Dec 2013
    Location
    Denver, CO
    Posts
    13,176
    Contact support. There was once a bug that did this several years ago that they resolved with a firmware update.

    Sent from my SM-G965U using Tapatalk

Similar Threads

  1. Change all dosing volumes at one time
    By buerscher in forum DŌS & DDR – Dosing and Fluid Metering System
    Replies: 6
    Last Post: 04-02-2022, 00:46
  2. Help! New DOS Setup for AWC
    By ddrueckh in forum Apex Programming for Dosing, ATO, and AWC
    Replies: 35
    Last Post: 03-19-2019, 06:17
  3. Neptune dos dosing incorrect amounts
    By Lamarjeepboy in forum A2 Apex/ApexEL and A3 Apex Pro/Apex/Apex Jr
    Replies: 1
    Last Post: 12-04-2017, 11:30
  4. Help AWC setup not following dos profile
    By fyveonit in forum DŌS & DDR – Dosing and Fluid Metering System
    Replies: 1
    Last Post: 11-07-2017, 20:53
  5. DOS dosing incorrect dosage
    By Batty in forum DŌS & DDR – Dosing and Fluid Metering System
    Replies: 2
    Last Post: 09-22-2016, 07:31

Bookmarks

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •