ATO_LO
ATO_HI
SumpLo
SwResL
Waterchange
Fallback OFF
Set OFF
If Output AWCDrain = ON Then ON
Defer 006:00 Then OFF
If Output AWCTIME = ON Then ON
AWCTIME
Fallback OFF
Set OFF
If Time 16:00 to 16:01 Then ON
Defer 001:40 Then ON
AWCDrain
Fallback OFF
If Output WaterChange = ON Then ON
If Output WaterChange = OFF Then OFF
If Output DrainDone = ON Then OFF
When On > 001:00 Then OFF
DrainDone
Set OFF
If SumpLo OPEN Then ON
If SwResL OPEN Then ON
If Output WaterChange = OFF Then OFF
Defer 006:00 Then OFF
AWCFill
Fallback OFF
If Output WaterChange = ON Then ON
If Output WaterChange = OFF Then OFF
If Output AWCDrain = ON Then OFF
If Output FillDone = ON Then OFF
FillDone
If ATO_LO CLOSED Then ON
If ATO_LO OPEN Then OFF
If ATO_HI CLOSED Then ON
If Output AWCDrain = ON Then OFF
If Output WaterChange = OFF Then OFF
Defer 006:00 Then OFF
SumpPump
Fallback OFF
If Output AWCDrain = ON Then ON
If Output DrainDone = ON Then OFF
SWResPmp
Fallback OFF
If Output AWCFill = ON Then ON
If Output FillDone = ON Then OFF
ATK
Fallback OFF
Set OFF
If ATO_LO OPEN Then ON
If ATO_HI CLOSED Then OFF
When On > 005:00 Then OFF
Defer 000:10 Then ON
Defer 000:04 Then OFF
Min Time 060:00 Then OFF
If Output WaterChange = ON Then OFF |
Lower float switch for normal water level on ATK
Upper backup float switch for ATK if ATO_LO fails
Low opt switch on FMM for WC to stop draining
Float switch at bottom of fresh SW drum on BoB
Virtual Outlet (VO) to turn on WaterChange
Turns OFF if communication is lost with Apex
Sets initial state to OFF before following code
Keeps the WC running
Keeps VO on for six minutes during water change
Turns WC on automatically at correct time
VO to start WC at set time
Turns OFF if communication is lost with Apex
Sets initial state to OFF before following code
Says to turn on WC at 16:00
Delays command until 16:01:40. Holds button for 20 seconds to start AWC.
VO to start draining
Turns OFF if communication is lost with Apex
If WC VO is ON Then it is ON
If WC VO is OFF Then OFF
Turns OFF when drain is done
Turns OFF when on > 1 min. Saves pump from running dry if SwResL fails. Fill takes 30 seconds.
VO that stops draining of water
Sets initial state to OFF before following code
If Low Float Switch is dry drain is done
If no fresh saltwater, stops WC
If WC VO times out then stops WC
Waits 6 min to turn stop the process.
VO that fills with fresh saltwater
Turns OFF if communication is lost with Apex
If WC VO is ON Then it is ON
If WC VO is OFF Then OFF
Cannot drain and fill at the same time
Turns off when refill is complete
VO that stops filling
Stops filling at lower float switch on ATK
Keeps filling until lower ATK float switch is reached
Stops filling if lower ATK float switch fails
Cannot drain and fill at same time
If WC VO times out then stops WC
Waits 6 min to stop the process, giving time for WC to finish.
Pump to remove saltwater
Turns OFF if communication is lost with Apex
If VO is ON then drain
If finished draining then OFF
Fresh saltwater pump in barrel
Turns OFF if communication is lost with Apex
Turn on to refill with water
Turn OFF when finished
ATK programming
Turns OFF if communication is lost with Apex
Sets initial state to OFF before following code
If lower ATK switch is dry then ON
If high ATK switch is wet then OFF
Turn OFF if running > 5 minutes
Do not turn back ON for at least 10 seconds
ATK will run for at least 4 seconds before turning OFF
ATK will not run for at least 60 min after turning OFF
Turns OFF ATK if WaterChange is ON to prevent filling with RODI instead of SW |
Bookmarks