Results 1 to 7 of 7

Thread: Probe Dimensions

  1. #1
    New User
    Join Date
    Dec 2018
    Location
    UK
    Posts
    5

    Probe Dimensions

    Hi All,

    Can someone tell me the size of the dimensions for the Apex 2016? I do not have much space to work with and think the probes will be to big as they are not submersible

    Regards,

    Zion

  2. #2
    Frequent Contributor zombie's Avatar
    Join Date
    Dec 2013
    Location
    Denver, CO
    Posts
    13,176
    You can print off the mounting templates to see where you can fit everything in your stand.

    The conductivity probe and temp probe are fully submersible. The orp and pH probes should be placed in a probe holder to keep the cap and cable above water.

    Sent from my SM-G965U using Tapatalk

  3. #3
    New User
    Join Date
    Dec 2018
    Location
    UK
    Posts
    5
    Many thanks for the reply, but as far as I am aware there are no templates for the probes? I want to know the actual dimensions of the probes themselves to see if I have room for them.

    Regards,

    Zion

  4. #4
    Frequent Contributor zombie's Avatar
    Join Date
    Dec 2013
    Location
    Denver, CO
    Posts
    13,176
    Its roughly 6" long by 0.5 inch diameter.

    Sent from my SM-G965U using Tapatalk

  5. #5
    New User
    Join Date
    Dec 2018
    Location
    UK
    Posts
    5
    Many thanks for the reply, unfortunately, I think these will be too tall for my tank due to the hood, I have 2 1/2" clearance above the waterline.

    Regards,

    Zion

  6. #6
    Master Control Freak RussM's Avatar
    Join Date
    Dec 2012
    Location
    California - US Pacific
    Posts
    22,463
    Quote Originally Posted by Zion View Post
    Many thanks for the reply, unfortunately, I think these will be too tall for my tank due to the hood, I have 2 1/2" clearance above the waterline.
    I ran an 20g AIO with a DIY cover over the back compartments for years with about that same amount of clearance.
    Please do not send me PMs with technical questions or requesting assistance - use the forums for Apex help. PM me ONLY if the matter is of a private or personal nature. Thanks.

  7. #7
    Frequent Contributor zombie's Avatar
    Join Date
    Dec 2013
    Location
    Denver, CO
    Posts
    13,176
    Quote Originally Posted by Zion View Post
    Many thanks for the reply, unfortunately, I think these will be too tall for my tank due to the hood, I have 2 1/2" clearance above the waterline.

    Regards,

    Zion
    You only need 1" clearance above the waterline.

    Sent from my SM-G965U using Tapatalk

Similar Threads

  1. Dimensions of Fs200
    By drsalomon in forum Fluid Monitoring Module (FMM), FMK, ATK, LDK, and FMM Accessories
    Replies: 0
    Last Post: 11-26-2020, 16:14
  2. Question: ATK Dimensions
    By LesPaulGtr in forum Pre-Sales Questions
    Replies: 1
    Last Post: 01-11-2019, 07:12
  3. LD-2 Dimensions
    By ProfessorNemo in forum Fluid Monitoring Module (FMM), FMK, ATK, LDK, and FMM Accessories
    Replies: 1
    Last Post: 04-21-2018, 18:09
  4. Cor 20 dimensions?
    By GugsJr in forum Apex Programming for Vortech, Tunze, & Other Controllable Pumps
    Replies: 2
    Last Post: 10-14-2017, 16:51
  5. Dimensions..please.
    By randoreefer in forum Apex Installation and Mounting
    Replies: 0
    Last Post: 10-17-2013, 10:42

Bookmarks

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •