Results 1 to 4 of 4

Thread: MP40's Programming

  1. #1
    New User
    Join Date
    Dec 2018
    Location
    London
    Posts
    2

    MP40's Programming

    Hi all I have a Reefer 350 with 2 x MP40 connected to Apex via WXM after weeks of trying placements for the MP40's in the tank back glass and sides trying to get percentages without blasting sand or LPS I have come to the conclusion running 1 x MP40 at a higher setting suits my tank much better and things are fine but where I require the help is I thought instead of using just the 1 MP40 I want to alternate between the 2 MP40 being on and off they are attached to the sides. I was OK using the wizard to program but a little lost on doing under the advance I had in mind

    VortechRight

    00:00 - 03:00 40% Lagoon
    03:00 - 06:00 OFF
    06:00 - 08:30 60% Reef Crest
    08:30 - 10:30 OFF
    10:30 - 13:00 55% NTM
    13:00 - 15:30 OFF
    15:30 - 18:00 65% Reef Crest
    18:00 - 20:30 OFF
    20:30 - 22-00 80% Pulse 0.56 intensity
    22:00 - 00:00 OFF



    VortechLeft

    00:00 - 03:00 OFF
    03:00 - 06:00 40% Lagoon
    06:00 - 08:30 OFF
    08:30 - 10:30 80% Pulse 0.56 intensity
    10:30 - 13:00 OFF
    13:00 - 15:30 65 % Reef Crest
    15:30 - 18:00 OFF
    18:00 - 20:30 65% Reef Crest
    20:30 - 22:00 OFF
    22:00 - 00:00 60% Reef Crest

    If anybody could point me in the right direction i would be very grateful

  2. #2
    Frequent Contributor zombie's Avatar
    Join Date
    Dec 2013
    Location
    Denver, CO
    Posts
    13,176
    You would be better off using the wizard. Just alternate between 0% and your desired percent and you will get a moving point of confluence and more turbulence without blasting anything.

    Sent from my SM-G965U using Tapatalk

  3. #3
    New User
    Join Date
    Dec 2018
    Location
    London
    Posts
    2
    Thank you for your advice I did try that but on any of the programs i set 0% they all were showing about between 40 and 60% in the fusion display causing the blasting problem

  4. #4
    Frequent Contributor zombie's Avatar
    Join Date
    Dec 2013
    Location
    Denver, CO
    Posts
    13,176
    Quote Originally Posted by Steveryan View Post
    Thank you for your advice I did try that but on any of the programs i set 0% they all were showing about between 40 and 60% in the fusion display causing the blasting problem
    Then either reduce the maximum, add two zero points in the wizard spaced like an hour apart, or a combination of the two.

    Sent from my SM-G965U using Tapatalk

Similar Threads

  1. Mp40 programming help
    By GugsJr in forum Apex Programming for Vortech, Tunze, & Other Controllable Pumps
    Replies: 3
    Last Post: 09-08-2017, 09:52
  2. Mp40 programming
    By jonnyedwards1981 in forum Apex Programming for Vortech, Tunze, & Other Controllable Pumps
    Replies: 2
    Last Post: 03-11-2016, 03:42
  3. MP40 Programming Help
    By AdamJ in forum Apex Programming for Vortech, Tunze, & Other Controllable Pumps
    Replies: 2
    Last Post: 08-18-2015, 18:24
  4. Help! Programming a new second MP40
    By Michael182 in forum Apex Programming for Vortech, Tunze, & Other Controllable Pumps
    Replies: 2
    Last Post: 12-06-2013, 05:49

Bookmarks

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •