Page 2 of 2 FirstFirst 12
Results 26 to 36 of 36

Thread: What am I doing wrong?!

  1. #26
    Frequent Visitor
    Join Date
    Sep 2018
    Location
    Florida
    Posts
    90
    If I were to want the led always on which wires would i switch?

  2. #27
    Frequent Visitor rkpetersen's Avatar
    Join Date
    Jun 2017
    Location
    Near Seattle
    Posts
    940
    From what I described above, just changing the + power from the left white wire to the red wire would do it. Then cap off the left blue and left white wires.

  3. #28
    Frequent Visitor
    Join Date
    Sep 2018
    Location
    Florida
    Posts
    90
    I ended up switching lights again, would you mind helping me with the wiring? I think I'm pretty close on this one. These were straight from China and didn't have any wiring diagram. 15499354686076829704024176670234.jpg

  4. #29
    Frequent Visitor rkpetersen's Avatar
    Join Date
    Jun 2017
    Location
    Near Seattle
    Posts
    940
    Without a wiring diagram, it's only a guess. I would guess that the black and red leads should go to the power supply and illuminate the switch constantly. One blue lead and matching yellow lead to the BOB. No idea if it's going to be normally open or normally closed As I said, just a guess, and if it's wrong, you could potentially damage your Apex.

  5. #30
    Frequent Visitor
    Join Date
    Sep 2018
    Location
    Florida
    Posts
    90
    Quote Originally Posted by rkpetersen View Post
    Without a wiring diagram, it's only a guess. I would guess that the black and red leads should go to the power supply and illuminate the switch constantly. One blue lead and matching yellow lead to the BOB. No idea if it's going to be normally open or normally closed As I said, just a guess, and if it's wrong, you could potentially damage your Apex.

    I think I found it. Let me know if this helpsScreenshot_20190212-130155.jpg

  6. #31
    Frequent Visitor rkpetersen's Avatar
    Join Date
    Jun 2017
    Location
    Near Seattle
    Posts
    940
    With this model, I don't think you can get the switch to toggle ON and the light to also come on at the same time, without also sending 24V to the BOB, which you don't want to do. Red and black leads to the power supply, leads 3 and 4 to the BOB.

  7. #32
    Frequent Visitor
    Join Date
    Sep 2018
    Location
    Florida
    Posts
    90
    Quote Originally Posted by rkpetersen View Post
    With this model, I don't think you can get the switch to toggle ON and the light to also come on at the same time, without also sending 24V to the BOB, which you don't want to do. Red and black leads to the power supply, leads 3 and 4 to the BOB.

    Can't believe it was that simple, I was hoping for the led to be off but from what you're guessing thats impossible?

  8. #33
    Frequent Visitor rkpetersen's Avatar
    Join Date
    Jun 2017
    Location
    Near Seattle
    Posts
    940
    Quote Originally Posted by brandonrush1 View Post
    Can't believe it was that simple, I was hoping for the led to be off but from what you're guessing thats impossible?
    I don't see a way to do it with that switch. You need two isolated sets of NC/NO leads, as you had with the other switch.

  9. #34
    Frequent Visitor
    Join Date
    Sep 2018
    Location
    Florida
    Posts
    90
    Well thank you again for all your help, I have a request in for a witiwi diagram for my specific button. If the diagram changes I'll post it here.

  10. #35
    Frequent Visitor
    Join Date
    Sep 2018
    Location
    Florida
    Posts
    90
    I was able to get a wiring diagram, any luck with this one?Screenshot_20190212-204316.jpg

  11. #36
    Frequent Contributor zombie's Avatar
    Join Date
    Dec 2013
    Location
    Denver, CO
    Posts
    13,176
    Quote Originally Posted by brandonrush1 View Post
    I was able to get a wiring diagram, any luck with this one?Screenshot_20190212-204316.jpg
    Not gonna work. You need two form A or Form C contacts and that switch only has one.

    Sent from my SM-G965U using Tapatalk

Page 2 of 2 FirstFirst 12

Similar Threads

  1. What am I doing wrong here?
    By Victor in forum APEX Fusion
    Replies: 4
    Last Post: 03-28-2020, 10:04
  2. Help! What did I do wrong?
    By OsiViper in forum DŌS & DDR – Dosing and Fluid Metering System
    Replies: 9
    Last Post: 05-10-2015, 10:34
  3. Question: What am i doing wrong
    By Mutley29 in forum APEX Fusion
    Replies: 5
    Last Post: 10-11-2014, 09:54
  4. Help what am I doing wrong
    By itsalifestyle in forum Apex Programming for Lighting
    Replies: 6
    Last Post: 12-05-2013, 11:07
  5. What am I doing wrong
    By Ivan in forum Apex Programming for Vortech, Tunze, & Other Controllable Pumps
    Replies: 2
    Last Post: 03-05-2013, 07:08

Bookmarks

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •