I didn't realize there was a 4.31 out, when I attached my Radions on V4.30 it worked fine until I came back from work and my tank was white. My apex reset itself to default (new IP address as well) and decided to start cycling my return pump on and off while dosing alk and cal for hours on end. as of now I cannot connect to my radions or my vortech pumps. the only thing that saved me was the pump cycling, it allowed enough time for the alk and cal to not fully get to the display but currently i'm at 15DKH and my SPS are not looking good at all. I'll upgrade to 4.31 tonight and see if anything starts working correctly.
There are still few bugs to work out. I just recently upgraded to the latest version about 2 nights ago. Ended resetting wxm, pumps and reattaching all. So far so good. I haven't seen additional virtual outlets popping up as I did on previous version
Everything was fine for a few days but now I'm starting to get multiple radions forming on my dashboard.
Did you updatebto the update? That fixes that issue
Sent from my HTC6435LVW using Tapatalk
Yes and it was fixed for a few days.
Hmm not sure, updating to the CD worked and solved that issue on my end.
Sent from my HTC6435LVW using Tapatalk
There's a cd?
I'm not involved in the beta. I didn't apply for it because I'm frankly too inexperienced with the Apex to feel comfortable doing so. I have been following the progress through these comment though, and I have to really commend everyone who is involved in this. It makes me feel confident that the RC1 will be a top quality product.
I posted this in another thread earlier today but I think it may get more attention here by the right people;
I have what I believe to be a pretty kick-butt Radion chart for my 90g mixed reef with SPS... I programmed it into the old controller interface a few weeks ago, but I have noticed some flickering of reds and greens while in the ramping 20k, 18k and 14k modes. I'm not sure why that is happening? Before I try to program the same schedule into Fusion (which could take quite a bit of time for a noob like me), I was wondering is someone could help me figure out why the flickering is happening? Does it have something to do with the power levels and fractions thereof with ramping? How do I fix it? Here is my chart with all the information used to create the profiles and commands... and here is my outlet programming information. I have two Radion Gen2s - Apex FW 4.31_2A14 - this issue is occuring during AUTO on both lights and when it happens it will happen to one light, then the other immediately after. It looks like it happens rhythmically, in series.
Capture.JPG
Fallback OFF
Set OFF
If Time 12:00 to 14:00 Then 20K_up
If Time 14:01 to 15:00 Then 18K_up
If Time 15:01 to 16:00 Then 14K_up
If Time 16:01 to 17:00 Then 12K_up
If Time 17:01 to 20:00 Then 12KPeak
If Time 20:01 to 21:00 Then 12K_dn
If Time 21:01 to 22:00 Then 14K_dn
If Time 22:01 to 23:00 Then 18K_dn
If Time 23:01 to 00:00 Then 20K_dn
If Time 00:01 to 01:30 Then MoonLight
Capture1.JPG
Thanks in advance for all the help and the GREAT PRODUCT! I apologize for the duplicate post.
Last edited by jnschlesinger; 02-09-2014 at 21:02.
HW Type HW Rev SW Rev Addr Name EB8 module 001 011(OK) 003 EB8_SPS EB8 module 001 011(OK) 004 EB8_DISP WXM module 000 008(OK) 005 WXM_Display Rev 1.11, RF Rev 1.2 (1,2,3,3),(2,3,3)
Vortech_5_1 - Rev 255.255 OK-1
Vortech_5_2 - Rev 1.5 OK-2
Radion_5_17 - Rev 0.0.0 - OK
Radion_5_18 - Rev 1.7.6 - OKWXM module 001 008(OK) 006 WXM_Basement Rev 1.1, RF Rev 1.2 (1,2,3,3),(0,0,0)
Vortech_6_1 - Rev 255.255 OK-1
Vortech_6_2 - Rev 255.255 OK-2PM1 module 001 002(OK) 007 PM1_7 EB8 module 001 011(OK) 009 EB8_Sump Display module 001 009(OK) 010 Disp_10
I am running 2 Pro radions.
Just installed them today. I did all thge proper firmware upgrades. They have never done anything but flicker. They respond to the slider but only flash the changes and then go dark.
PLEASE HELP. I am without light.
Where did u get the 2A14 from? The 1E14 was just released 6 days ago. I have gen2 and I had the same problem with the firmware before CD13, After the CD13 was installed that flicking issue was fixed on mine, then this 1E14 was released and updated. So far no issues.
Sent from my iPhone using Tapatalk
Oh Ok, didn't know that
Sent from my iPhone using Tapatalk
I wasn't aware of that either. Anyhow, I still have the same problem and I have updated the firmware, deleted/reinstalled the outlets and the module, power cycled the unit and the WXM, and so on. Anyone have a solution?
I am still running 1.6.7 on my Gen2 Radions, with the latest 4.31 E Apex firmware. Not having any issues...
I've been periodically losing Radion and Vortech connection...
What version of Apex FW are you running? 4.31_2A14What is the SW Rev, WXM Rev, and WXM RF Rev? SW Rev 08, WXM Rev 1.11, RF Rev 1.2What type of light do you have (Gen1, Gen2, or Pro?) 3 (Gen2) Radio Pros and a Gen2When an issue is occurring can you manually control the lights on/off? No
that happened to me on previous beta firmware, but hasn't happened yet on the new "E" version....
A little frustrating. Mine is doing the same thing.
I am in the beta version, actually, and it did not happen to me before. Maybe that information will be helpful to somebody.
This morning after the issue I reapplied all firmware. I have not had the issue since, but that doesn't necessarily mean it's fixed. I believe the first time it took 8 hours.
Bookmarks