Ok RussM this is really doing my head in.
This is a where I'm at, I got all of the 6 outlets to work what I did was just slide to ON you can see on the pic all were working fine...
sexxxxx.png
Ok RussM this is really doing my head in.
This is a where I'm at, I got all of the 6 outlets to work what I did was just slide to ON you can see on the pic all were working fine...
sexxxxx.png
ON and OFF on the sliders are manual override. You need to rename and program each one for the intended use. Then put the slider in AUTO so the programming can be executed.
Please do not send me PMs with technical questions or requesting assistance - use the forums for Apex help. PM me ONLY if the matter is of a private or personal nature. Thanks.
Click the cog icon above a slider to get into the outlet programming area.
Please do not send me PMs with technical questions or requesting assistance - use the forums for Apex help. PM me ONLY if the matter is of a private or personal nature. Thanks.
I would like these done:
Chiller has two outlets
Heater
Return Pump
Tank Pump
Skimmer
2 x Radions
ATO
and others like Cabinet light , 2x Cams, as you can see I need 10 or so outlets...but there are only 6 on my EB so how would you use all of the plugs needed , can I piggy back these..thinking would mess the programs up...or need another EB6...is this correct?
I have a Skimmer program completed can you check for me please , if power is lost I want the skimmer to come on after 5 min when restored?
Fallback OFF
Set ON
If Outlet Maint2 = ON Then OFF
If Power EB6_3L Off 005 Then OFF
Defer 005:00 Then ON
Hello
You really need to tell what you want to do ...
Otherwise it will be very difficult.
Sent from my XT1092 using Tapatalk
The skimmer program is probably OK. But adding a line like If ReturnPump = OFF Then OFF probably has merit.
Chiller: use the wizard
Heater: use the wizard
Return pump:
Fallback ON
Set ON
Tank pump: ? too vague what kind of pump?
Radions: DO you have an WXM or not? That makes a big difference.
ATO: Cant help here too vague/not nearly enough info. You don't even say what sort of ATO it is - standalone ike JBJ or Tunze? DIY?
Plug the cams into regular power; it's a waste of an EB outlet
Please do not send me PMs with technical questions or requesting assistance - use the forums for Apex help. PM me ONLY if the matter is of a private or personal nature. Thanks.
Why isn't the skimmer program working was wanting a 5 min delay if power was interrupted.
Untitled.png
The error message tells you. Before you can reference an outlet name in programming, there must be an outlet by that name. All names of outlets, profiles, probes, and switches are case-sensitive, BTW.
Please do not send me PMs with technical questions or requesting assistance - use the forums for Apex help. PM me ONLY if the matter is of a private or personal nature. Thanks.
OK so where is the outlet for Skimmer?
It's complaining that you done have an outlet called Maint2, and that you don't have an EnergyBar named EB6_3L
Did you simply copy someone else's skimmer programming and are trying to use that without adapting it for your system?
Please do not send me PMs with technical questions or requesting assistance - use the forums for Apex help. PM me ONLY if the matter is of a private or personal nature. Thanks.
how is this one...
Fallback OFF
Set ON
If Outlet Skimmer = ON Then OFF
If Power EB6_3 Off 005 Then OFF
Defer 005:00 Then ON
That wont work. You need to name your return outlet before you code this. Then you want the code below. Replace the word Return with whatever you called your return outlet.
Fallback ON
Set ON
If Outlet Return = OFF Then OFF
If Power EB6_3 OFF 001 Then OFF
Defer 005:00 Then ON
You might be an engineer if...You have no life and can PROVE it mathematically.
Like this..
Untitled 3.png
Fallback ON
Set ON
If Outlet Returnpump = OFF Then OFF
If Power EB6_3 Off 001 Then OFF
Defer 005:00 Then ON
How do I know is there a way to check it..
it's not enabled.
The enabled refers to logging and nothing more. If you want to be able to look into your past logs to see when the outlet turned on or off, you want it enabled.
You can check which outlet is the correct one by looking to see which outlet the device is actually plugged into. They are numbered like this with the power cord to the left. You should have the outlet name you give it relate to whats plugged into it.
1 2 3
4 5 6
You might be an engineer if...You have no life and can PROVE it mathematically.
Yes mine are labeled.
So the wizard will let me know if there was a error..
It will let you know if there is a syntax error. To see if it will functionally work, you need to test it with the equipment youre ginna plug in and see if it operates how you think it should.
You might be an engineer if...You have no life and can PROVE it mathematically.
Hello all,
sorry for waking up old thread. I did full reset on my Apex Classic. But in Fusion and Classic only one socket appears. I hear some relays clicking when EB6EU is starting. Nothing more after. Is this bar damaged (i bought it used) or is some kind of other problems?
Screenshot of Fusion below:
IMG-20171001-WA0021.jpg
Thank you,
Spyder
Bookmarks